Tile Edge Trim After Tiling (How To Fix It?)

Can you Tile Edge Trim After Tiling? Yes, but it also depends on your past actions. Are you simply adding more tiles, or did you place the second one against the edge, eliminating any opportunity for an edge? Let’s assume you made a terrible mistake.

The worst-case condition is that you have to remove the top course, the mastic, or the thin set to apply a new layer, and then you have to cut the tile to fill in the gaps once the edge has been installed. Even though it could be a better job, it might work. Alternatively, start over and complete it right the next time. If you put forth the effort, anything can be accomplished.

Tile Edge Trim After Tiling – Fixed

Install spacers after tiling to fill the area between each tile evenly. After that, installing the edge trim is simple. Second, you must cut the tiles close to the edge to install the trim. As it is simple to slide and get cut with a wet tile, saw, this can be a challenging and risky task.

Choosing The Right Trim For Your Tile

It’s time to choose an edge trim once you’ve completed half the tiling. There are four different sorts of trims available. Which are:

• Stone Trims
• Plastic Trims and 
• Porcelain or ceramic trims
• Metal Trims

The stone trims are frequently utilized on the interior or on showers’ walls. They are substantial and simpler to install. Additionally, they appear seamless, which you may emphasize by cleaning the outside. However, they are somewhat costly. 

Another form of trim is ceramic tiles. However, they are typically used for bullnose edges with a wider radius. These are only sometimes used today, but you can request this specifically.

Plastic and metal can be found in different colors, sizes, and shapes. The metal embellishments are well-liked and inexpensive. But there’s also a more pricey choice. These are frequently used for shower walls, floors, etc.

However, abrasion is a major concern for plastic trims. They are, therefore, less frequently utilized.  You are now educated enough to select and set up your new embellishments.

How To Trim The Edge Of A Tile?

Rough surfaces might be better for your freshly furnished home, though. Therefore, it is preferable to trim the edges of your tiles once you have finished tiling. It looks fantastic and provides a much smoother finish.

Additionally, you can cover your tiles with carpet to improve their appearance. This won’t harm your flooring but will undoubtedly give the space a cozy atmosphere. Let’s now look at how to install one!

Tools Required

You’ll need some tools to trim the tile edges. What’s on the list?

• Tape measure’s hook
• Clamps
• Mitre box
• Hacksaw or Trim cutter
• Adhesive
• Chalk
• Grout
• Trowel
• Sealer

Let’s begin putting the trimmings once everyone has gathered their tools!

Step 1: Planning Trim Placement

Your tile trim can now be installed in two locations. You can position it at the corners or the base of the wall. Additionally, you’ll need to schedule the trimming procedure to coincide with the installation of your tiles. Otherwise, you might not pick the appropriate tile trim type. 

Step 2: Measuring The Trim

Right now, you must measure the floor’s corners and base. Or really, everywhere you’re putting down tiles.  This will also enable you to determine how much trim you’ll require for the job.  Now, use the hook on your tape measure to precisely measure the thickness of the locations.

Then write it down for later use. For this, you’ll need the exact measurements of the bottom and the four walls’ corners. To ensure you don’t leave any spaces unfilled, measure the distance between the tile & the wall. If not, you may need to do what comes next again. 

Step 3: Cutting The Trim 

It would help if you now cut the trimmings based on the measurements you took earlier. You can now cut it straight to make the trimmings. Wall bases and edges should always be at a 45° angle.

You’ll require a mitre box to cut it. This is available in any hardware shop.  Clamps should first be used to secure one of the trim’s sides. You are setting it securely in place. After that, utilize your mitre box as a cutting guide.

Use a hacksaw or trimmer to make the necessary cuts based on dimensions. Continue doing this for all the others. Ensure each trim forms a 90° angle when aligned in a line. In light of this, we will proceed to the subsequent action.

Step 4: Mark & Glue Down The Trim

Mark the area on which the trim will be applied first. Make the markings with chalk. This will serve as a template for applying adhesive.

Now use a trowel to apply your adhesive following the line. To ensure that the tile adheres to the glue, place it and push firmly. For the remaining trims, repeat. Allow it to dry overnight after that.

Step 5: Grout And Seal The Trim

• Prepare to grout and seal after the adhesive has dried. Apply the grout first where there are gaps.
• Keep for a minimum of 2 days to make it dry.
• The grout should then be sealed. The group’s performance and durability will improve as a result. After that, let it a full day to dry.
• For the installation of the trim, that is it. The remainder of your tiling project may now proceed.

Conclusion

That is how Tile Edge Trim After Tiling. It was a rather easy process. So why are you still waiting? Immediately begin your work!  Have a Good day, and I hope to see you soon!

Frequently Asked Questions